HASSLEBLAD ELM REPAIR MANUAL PDF

Correction in Service Manual. CX New camera body – new parts .. The operation (except ELX) is fortunately a matter of minutes only. Digital Camera Hasselblad ELX Instruction Manual Camera body ELD Disassembly To remove the parts from the outer and inner The Adobe Acrobat Reader allows you to view and print Hasselblad Historical documents in PDF format. A free copy of the Acrobat Reader is available from.

Author: Malaramar Arashitaur
Country: Belize
Language: English (Spanish)
Genre: Travel
Published (Last): 17 October 2016
Pages: 358
PDF File Size: 16.23 Mb
ePub File Size: 6.74 Mb
ISBN: 113-1-81620-654-6
Downloads: 62120
Price: Free* [*Free Regsitration Required]
Uploader: Dozil

500 EL/M won’t fire with pressing of release button

Front bayonet plate and auxiliary shutter Exploded view: Motor housing Exploded view: IR Release unit Revision 0 May Unit for infrared remote release of the Hasselblad ELD. Attaches to the front release ports of the camera and powered by the camera batteries. Can be set for normal or digital photography. Supplied with the Hasselblad IR Remote controlwhich in normal conditions provides an operating range of approx.

Camera body ELD Disassembly Remove the tripod foot by removing the six screws and the rubber support held by double-sided tape. When the tripod foot and the rubber hassleblad have been removed, four holes are exposed allowing access to the four screws Elmm body ELD Disassembly To remove the parts from the outer and inner mounting plates proceed as follows see the exploded views 13 and Remove the small nuteccentric and bearing pin Remove the screw Camera body ELD Disassembly Remove the two long screws located towards the front of the camera shell.

Remove the two short screws located towards the rear of the camera shell.

Remove the cap from the chassis connector and peel back the leather covering the two screws Camera body ELD Disassembly Rear plate Remove the screw from the centre of the large gear and lift the gear clear. With the gear removed an additional screw is exposed which must also be removed Camera body ELD Disassembly Mirror Disconnect the mirror hinge from the two pins “A” and release the pin “B” on the mirror frame, from the mirror lever The complete mirror can now be separated from the remainder of the assembly.

Camera body ELD Disassembly Right and left hand wall Remove or cut the foam plastic pad to get access to the screws The dismantling procedure for the Hasselblad ELD is now completed.

Revision 0 May Use the lubricants listed below: Fit the washer followed by the B-armthen fit the washer followed by the S-arm EPS Refit the gearwheel temporarily.

This should be between 40 and 60 grams. Adjust by bending the spring as indicated in Fig. EPS Fig. This is done by turning gear Note that the pin “A” should be visible from “B” the outside. Camera body ELD Reassembly The key position of the front gear is checked with the Position for screw driver camera cocked.

This is carried out as follows: Make sure the camera is released. Locate the mirror into position. Connect the mirror hinge to the two pins “A”. Camera body ELD Reassembly Seal between the rear plate and the left side wall using black silicone or similar as shown in Fig. Camera body ELD Reassembly Place the ruler with indicator clock onto the gauge and move the indicator around the periphery on the front plate and check that the length is within the tolerance.

  DESCARGAR LIBRO LA UNCION DE BENNY HINN PDF

If the camera body is too short, on the left-hand side, then the front must be moved forward on this side. Turn the gear in a clockwise direction until the check “C” Disengagement should occur when the check “D” has passed the locking arm and moved a further 1 – 2 mm. Check that the auxiliary shutter blinds do not influence on the light path. When handling the circuit board a grounded bench mat and a wrist strap must be used to prevent ESD damage.

Fit the circuit board in position. It is fixed to the Lubricate with Isoflex Topas L32 onto the pin for the teflon button and put that one in position before inserting the camera body into the camera shell.

Fit the rubber support Fit the tripod foot and secure it with the six screws When the wiring has been correctly connected, re- assemble the outer mounting plate by using the following sequence: Secure the stop armby refitting the bearing pinthe eccentricthe small nut and secure by the clip If there is no exposure operation, one reason for this can be that the release lever is not releasing the cocked action between the release arm and repsir release catch Camera body ELD Adjustment Check that the flat side of gear is parallel with the rear section.

Repqir source of current must be removed before adjustment is carried out.

Hasselblad camera repair and maintenance advice.

If the position of gear is faulty in relation to rear section, this can be adjusted by modifying engagement with gear Camera body ELD Adjustment RS – Repeated pre-release The same function occurs as in the S position except that the selector knob remains in the set position and the camera returns automatically to the S position after exposure until the selector knob is returned manually to the 0 position.

Camera haassleblad ELD Adjustment Check that the magnet arm has free movement between the shanks of spring during exposure.

Bend the front shank of spring yassleblad. Check the spring blocks the magnet arm when the T-arm is in the L position. Camera body ELD Adjustment Checking the databus connections Check the integral control connector to ensure automatic and direct communication between camera body and digital back.

Proceed using the following sequence: Camera body ELD Adjustment Check the mirror 45 angle using the sighting tube which fits in the holder on the gauge. Tighten the locking screw.

HASSELBLAD Camera Manuals

Shine a light source towards the oval cut-out in the upper part of the tube so that the white ring of the ocular is illuminated. Camera body ELD Front bayonet plate Front plate reassembly Fit the four bayonet tongues and secure with eight screws Behind the front plate glue the two foam plastic strips and as well as the reflection protector into place.

Use tool V for driving in the pin. Drive the pin in until the face of the tool touches the front bayonet plate. For convenience use the aux. Remove the pinspring retainer, spring and the upper actuating arm Camera body ELD Page of 84 Go. Add to my manuals Add. Page 9 Camera body ELD Disassembly Remove the tripod foot by removing the six screws and the rubber support held by double-sided tape.

  ARCHEXTERIORS 17 PDF

When the tripod foot and the rubber support have been removed, four holes are exposed allowing access to the four screws Page 10 Camera body ELD Disassembly To remove the parts from the outer and inner mounting plates proceed as follows see the exploded views 13 and Remove the screw Page 11 Camera body ELD Disassembly Remove the two long screws located towards the front of the camera shell.

Page 12 Camera body ELD Disassembly Rear plate Remove the screw from the centre of the large gear and lift the gear clear. Page 13 Camera body ELD Disassembly Mirror Disconnect the mirror hinge from the two pins “A” and release the pin “B” on the mirror frame, from the mirror lever Page 14 Camera body ELD Disassembly Right and left hand wall Remove or cut the foam plastic pad to get access to the screws Page 15 and cable holder Page 23 Camera body ELD Reassembly Seal between the rear plate and the left side wall using black silicone or similar as shown in Fig.

Page 24 Camera body ELD Reassembly Place the ruler with indicator clock onto the gauge and move the indicator around the periphery on the front plate and check that the length is within the tolerance. Page 35 Camera body ELD Adjustment RS – Repeated pre-release The same function occurs as in the S position except that the selector knob remains in the set position and the camera returns automatically to the S position after exposure until the selector knob is returned manually to the 0 position.

Page 36 Camera body ELD Adjustment Check that the magnet arm has free movement between the shanks of spring during exposure.

Page 37 Camera body ELD Adjustment Checking the databus connections Check the integral control connector to ensure automatic and direct communication between camera body and digital back.

Page 38 Camera body ELD Adjustment Check the mirror 45 angle using the sighting tube which fits in the holder on the gauge. Page 41 Camera body ELD Front bayonet plate Front plate reassembly Fit the four bayonet tongues and secure with eight screws Page 48 Camera body ELD Page 53 Camera body ELD hasslsblad Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page.

To print the manual completely, please, download it.

Hasselblad 555ELD Service Manual

Don’t show me this message again. Got it, continue to print. Don’t have an account?